Ole Bird Quilt Shop, make your own bird house.

Building an ornamental bird house.

I'm building another bird house much like the one I did for the guild raffle, only this time I'll post it for sell.  This bird house could be used outside to house blue birds that visit your yard however, why would you.  These things are so cute you'd want it to last a life time right?

Anyway, I decided I'd post some pictures of the progress so you can see how I built this one.

These three top pictures are of the parts cut out and sanded ready for assembly.  The middle part of the bird house consists of 4 pieces of wood while the sides are only 3 side because they attach at the sides of the middle or main house.

Cut list

Middle section

2 -  8 (which is about 7.5 inches actually) x 24 inch pieces that are mitered at the top at center of each board so that they stay 24 inches in length.  Cut two holes about 2 inch diameter and drill 1/2 inch holes under these holes going only half way through.  You will use the bottom holes to add the dowel perch. 

2 - 21x8 compound mitered at one end.

Side sections

4 - 8x 8 and 7/ 8 inch pieces compound mitered at one end

2 - 8x11 inch pieces  that are mitered at the top at center of each board so that they stay 11 inches in length  On each of these boards cut one hole about 2 inch diameter and drill 1/2 inch hole under this hole going only half way through.  You will use the bottom holes to add the dowel perch. 

Middle section roof

2 pieces cut at 7 and 7/8 x 6 and 1/2 inches with compound miter at one of the long ends so they stay at 6  and 1/2 inches in length. 

Side section roof.
4 pieces cut at 7 and 7/8 x 4 inches with compound miter at one of the long ends so they stay at 4 inches in length.

3 - 1/2 x 3 inch dowels to use as perches. 

Columns

Cut one stair spindle to 21 inches and then cut in half lengthwise using a band saw

Sand all pieces on all sides including the bottoms and tops of the boards.

Begin by gluing and nailing the two  8 x 8 and 7/8 inch pieces  that are compound mitered at one end to one of the 21 x 8 compound mitered at one end. as shown below.  Make sure when you assemble these that the compound miters on all sections are facing out.  I hope you can see this below or in one of the following pictures.  If you nail these up incorrectly your roof will not fit properly.

Do this to both of the 21 x 8 compound mitered at one end. as shown below.  Notice the compound miter direction of all these boards.

Now attach the two 24 inch front and back to these two side pieces you've made.  The front and back fit inside of the two sides not on top as shown in the picture below.

Now if you have placed the compound mitered boards facing the correct direction your roof should fit perfectly onto your 3 sections.   At the now using glue and nails.  Do not worry if there is a gap at the top.  You will fill this with caulking later, and you will be adding shingles that will hide this gap.

Now add the stair spindles to either side of the middle house covering the seam.  You will have to notch the spindles so that they will fit around the side roof on each side.   Notice my notches I cut out of the spindles.

Next you will counter sink all nails and using a wood filler you will fill all the holes.  You will use caulking to fill all the gaps around the roof and on the roof line and any seams that seem to not fit perfectly together. When you paint, the paint will not hide cracks so this is important.  Let this dry over night.  Then hand sand the excess away so that you don't have lumps.  Lumps can not be hidden with paint.

Adding shingles and staining them.

Staining the shingles

Paint the main body one side at a time.  Let each side dry before moving on to another side.  Add 2-3 coats on each side sanding in between coats.

Decorate and paint as you wish.  Here it is finished.